- New Holland 275 Baler Specifications
- New Holland 275 Square Baler Specs For Sale
- New Holland 275 Baler Manual
- New Holland Square Baler Specifications
Twine Troubleshooting
Operators who custom bale, especially for horse farms, are big fans of New Holland square balers. New Holland bales are the only choice for hand-feeding because they quickly separate into flakes. Professionals put their trust in BC5000 model balers because they make consistently dense, well-shaped bales that are easy to handle. The secondary shaft that drives the gearbox for the feeder assembly had a catastrophic failure, causing the baler to get knocked out of time and a collision. Below are the general dimensions for the New Holland Hayliner 271 Baler. You can find the manual here. HAYLINER 271 BALERSPECIFICATIONS Length over-all bale chute up 15' 9' Length over-all bale chute down 18' 3' Width over-all 8' 2' Height over-all engine model 67' Height over-all p.t.o. Model 52' Pickup width 56'. I have been looking at various New Holland small square balers and hay harvesting implements in local auction listings.Can anyone advise of a website/ reference list where Model numbers and specs are listed of older NH small balers and haybines are listed.It would greatly reduce time of my search although I don't usually need an excuse to go to an olde farm auction.
The knot did not strip off the billhook
There’s a simple knot in twine over the bale but no knot in needle twine
There’s a simple knot in the needle twine
The twine breaks at the knot
Twine in the knot is ragged
There’s no knot in either twine
I’m getting a double bow knot
The twine ends are frayed or uneven
I’m running into other issues
How to pinpoint the problem
Problem: The knot did not strip off the billhook.
Excessive billhook tension can cause this; decrease tension. Or the billhook may need replacing if it’s rough, worn or bent. Is the knife arm not rubbing the billhook? Adjust or replace it. If the knife arm does not travel far enough, check lobe in cam gear and knife arm roller.
Problem: There’s a simple knot in twine over the bale but no knot in needle twine.
It could be caused by improper twine finger action; adjust to baler manual specifications. Or the needle did not place twine in twine disc, so adjust the needle to specifications and check tensioner at twine box. See if hay dogs are malfunctioning.
Problem: There’s a simple knot in the needle twine.
New Holland 275 Baler Specifications
The twine pulled out of the twine disc. Tighten twine holder and decrease twine box tension.
Problem: The twine breaks at the knot.
Sharp edges may be in the knife arm; smooth the knife arm or replace it. Or you may have too much bale tension; decreasing tension should fix it.
Problem: Twine in the knot is ragged.
The twine holder is too tight, which doesn’t allow the billhook to borrow twine when it rotates. To repair, loosen the twine holder.
Problem: There’s no knot in either twine.
Look for a lost or sheared pin in billhook pinion gear. Inspect the trigger roller and trigger pin. Check that trigger is not bent.
New Holland 275 Square Baler Specs For Sale
Problem: I’m getting a double bow knot.
This means the billhook tension is too light or that the billhook pinion gear has too much wear. Try tightening billhook tension or replacing billhook pinion gear.
Problem: The twine ends are frayed or uneven.
Problem: I’m running into other issues.
Is the hay being baled when it’s too green or wet?
New Holland 275 Baler Manual
How to pinpoint the problem.
When you find yourself at the end of your rope, trip the knotter mechanism and run the tying cycle through slowly. Most of the time the problem can be pinpointed when the tying cycle can be viewed in its entirety.
New Holland Square Baler Specifications
Navigate: